아날로그 전화기 발신번호가 표시 되지 않을 경우

증상1. 아날로그 전화기 발신번호가 표시 되지 않을 경우

 

구성 : VG310 / CM / 전화기는 SCCP로 교환기에 등록 함

 

해결 :

1. VG310 옵션값을 조정함

 ==> 각 voice-port 마다 옵션 지정 함

 ==> caller-id enable

 ==> 그래도 해결안됨

 

2.  cptone KR 옵션값을 삭제 해봄

 ==> cptone KR 옵션을 삭제하면 caller ID Info 에서 유형이 Standard BELLCORE로 변경됨을 확인

 ==> voice-port 마다 옵션값을 넣어서 caller info 유형을 변경 함

 

** caller ID Info 변경확인 명령어

> sh voice port 0/0/0

 

KRHKRFXSVG01#sh voice port 0/0/0

Foreign Exchange Station 0/0/0 Slot is 0, Sub-unit is 0, Port is 0
 Type of VoicePort is FXS  on-BOARD-24FXS
 Operation State is DORMANT
 Administrative State is UP
 No Interface Down Failure
 Description is not set
 Noise Regeneration is enabled
 Non Linear Processing is enabled
 Non Linear Mute is disabled
 Non Linear Threshold is -21 dB
 Music on Hold Threshold is Set to -38 dBm
 In Gain is Set to 0 dB
 Out Attenuation is Set to 3 dB
 Echo Cancellation is enabled
 Echo Cancellation NLP mute is disabled
 Echo Cancellation NLP threshold is -21 dB
 Echo Cancel Coverage is set to 128 ms
 Echo Cancel worst case ERL is set to 6 dB
 Playout-delay Mode is set to adaptive
 Playout-delay Nominal is set to 60 ms
 Playout-delay Maximum is set to 1000 ms
 Playout-delay Minimum mode is set to default, value 40 ms
 Playout-delay Fax is set to 300 ms
 Connection Mode is normal
 Connection Number is not set
 Initial Time Out is set to 60 s
 Interdigit Time Out is set to 60 s
 Call Disconnect Time Out is set to 60 s
 Supervisory Disconnect Time Out is set to 750 ms
 Ringing Time Out is set to infinity
 Wait Release Time Out is set to 30 s
 Companding Type is u-law
 Region Tone is set for US

 Analog Info Follows:
 Currently processing none
 Maintenance Mode Set to None (not in mtc mode)
 Number of signaling protocol errors are 0
 Impedance is set to 600r Ohm
 Station name None, Station number None

 Caller ID Info Follows:
 Standard BELLCORE
 Output attenuation is set to 14 dB
 Caller ID is transmitted after 1 ring(s)
 Translation profile (Incoming):
 Translation profile (Outgoing):
 lpcor (Incoming):
 lpcor (Outgoing):

 Voice card specific Info Follows:
 Signal Type is loopStart
 Ring Frequency is 25 Hz
 Hook Status is on Hook
 Ring Active Status is inactive
 Ring Ground Status is inactive
 Tip Ground Status is inactive
 Digit Duration Timing is set to 100 ms
 InterDigit Duration Timing is set to 100 ms
 Hookflash-in Timing is set to max=1500 ms, min=300 ms
 Hookflash-out Timing is set to 400 ms
 Disconnect acknowledge
 Ring Cadence is defined by CPTone Selection
 Ring Cadence are [20 40] * 100 msec
 Ringer Equivalence Number is set to 1
KRHKRFXSVG01#